Free Download Latest 2014 Pass4sure&Lead2pass Citrix 1Y0-A21 PDF (71-80)

QUESTION 71
Scenario: An administrator is planning the necessary configurations on a NetScaler system for an environment that requires the NetScaler system to advertise virtual IP addresses, directly connected routes and static routes on the upstream routers. What must the administrator ensure is configured on the NetScaler system for this environment?

A.    Static Routes
B.    Link Load Balancing
C.    Route Health Injection
D.    Front-end Health Check

Answer: C

QUESTION 72
Scenario: An administrator installed a NetScaler system and configured the NSIP and MIP for the system. The NetScaler system will be used primarily for load balancing in this environment. Which additional step must the administrator take to ensure that the NetScaler system can perform the necessary server load balancing in this environment?

A.    Disable USIP mode on both nodes
B.    Use the MIP as the NSIP for a high availability environment
C.    Create VIPs for the front-end connections to the back-end servers
D.    Enable USNIP mode for the front-end connections to the back-end servers

Answer: C

QUESTION 73
Scenario: A network administrator is deploying a NetScaler system in an environment with a single subnet using this IP information:
subnet: 192.168.10.32
netmask: 255.255.255.224
default gateway: 192.168.10.40
The administrator already set up the NSIP and MIP addresses using the command line interface. Which command could the administrator use to complete this set up successfully?

A.    add route 0.0.0.0 0.0.0.0 192.168.10.32
B.    add route 0.0.0.0 0.0.0.0 192.168.10.40
C.    add route 0.0.0.0 0.0.0.0 192.168.10.62
D.    add route 192.168.10.0 255.255.255.224 192.168.10.32
E.    add route 192.168.10.0 255.255.255.224 192.168.10.62

Answer: B

QUESTION 74
Scenario: An administrator is configuring a NetScaler system in one-armed mode. The NetScaler appliances are connected to the network through a switch and will be configured as a pair with high availability (HA) enabled.
Which two steps should the administrator take to succesfully configure HA in this environment? (Choose two.)

A.    Ensure the NSIP is identical on both systems
B.    Configure a unique nsroot password on each node of the HA pair
C.    Disable all system interfaces except the one connected to the switch
D.    Configure a Remote Procedural Call (RPC) node password on each node of the HA pair

Answer: CD

QUESTION 75
Which command can an administrator use to set up a NetScaler system to use SNIPs instead of MIPs for connections to local resources?

A.    set ns ip snip -mip
B.    set ns mode USNIP
C.    add ns mode USNIP
D.    enable ns mode USNIP

Answer: D

QUESTION 76
Scenario: An administrator is configuring the NetScaler-owned IP address for a network environment where the NetScaler IP, the mapped IP, and the back-end servers will be located on separate subnets. The administrator wants to create as few additional routes on devices, such as the servers, as possible while maintaining the communications between the NetScaler and the other devices.
Which two steps can the administrator take to achieve this? (Choose two.)

A.    Enable USIP mode
B.    Configure VIPs for the devices
C.    Ensure USNIP mode is enabled
D.    Make the MIP and the NSIP address the same
E.    Configure SNIPs on the subnets of the devices

Answer: CE

QUESTION 77
An administrator is deploying a NetScaler system using the command line interface and plans to configure the MIP as 10.48.192.17.
Which command must the administrator use to correctly configure the MIP for this NetScaler system?

A.    set ns config -ipaddress 10.48.192.17
B.    add ns ip 10.48.192.17 255.255.255.0 -type mip
C.    add ns config -ipaddress 10.48.192.17 -subnet mask 255.0.0.0
D.    set ns ip -ipaddress 10.48.192.17 -netmask 255.255.255.0 -mip

Answer: B

QUESTION 78
During the initial setup of a NetScaler system, an administrator can use the __________ command to correctly set the nsroot password. (Choose the correct option to complete the sentence).

A.    passwd
B.    set rpc node
C.    set system user
D.    add nsroot password

Answer: C

QUESTION 79
An administrator is setting up high availability (HA) using the command line interface. Which additional step should the administrator take to configure HA when using the command line interface?

A.    Reboot the primary node
B.    Specify each interface number
C.    Synchronize the SSL certificates, start up scripts and other configuration files on the primary node
D.    Manually disable the HA monitor for each interface that is not connected or not being used for traffic

Answer: D

QUESTION 80
Scenario: An administrator is configuring two NetScaler appliances for high availability (HA) using the command line interface. The administrator plans to have the primary NetScaler have the NSIP address 172.16.200.52 and the secondary NetScaler to have the NSIP address 172.16.200.53.
Which two command line interface commands could the administrator use to configure HA in this environment? (Choose two.)

A.    add node 1 172.16.200.53 on primary
B.    add node 0 172.16.200.53 on primary
C.    add node 0 172.16.200.52 on secondary
D.    add node 2 172.16.200.52 on secondary

Answer: AD

If you want to pass Citrix 1Y0-A21 successfully, donot missing to read latest lead2pass Citrix 1Y0-A21 exam questions.
If you can master all lead2pass questions you will able to pass 100% guaranteed.

http://www.lead2pass.com/1Y0-A21.html